Marantz SR6003 User Manual download pdf (Page 45)

ENGLISH

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

ADVANCED

OPERATION

ADVANCED OPERATION

AMP OPERATION

USING THE SLEEP TIMER

To program this unit for automatic standby, press the

SLEEP button on the remote controller.

Each press of the button will increase the time before

shut down in the following sequence.

OFF 10 20 30 5040

100 90 80 70 60110120

The sleep time will be shown for a few seconds in the

display on the front panel, and it will count down until

the time has elapsed.

When the programmed sleep time has elapsed, the

unit will automatically turn off.

Note that the SLEEP indicator on the display will

illuminate when the Sleep function is programmed.

To cancel the Sleep function, press the SLEEP

button until the display shows “SLEEP OFF” and the

SLEEP indicator will disappear.

DISPLAY MODE

You can select the display mode for the front display

of the unit.

To select this mode, press the DISPLAY on the

remote controller or the front panel.

When this button is pressed, the display mode is

switched in the following sequence.

Normal → Volume → Auto display OFF → Display

OFF → Normal Mode

Normal mode:

The following three mode types are displayed.

• Displays the selected input function. If the

function has been renamed using the Function

Rename feature (see page 28), the renamed

name appears on the display.

• Displays the input mode set via the Function

Input Setup feature. (See page 27)

• Displays the status of the selected surround

mode.

Volume mode:

The input function and input mode are displayed

in the upper part, and the current volume level is

displayed in the lower part.

Auto Display Off mode:

The display is off. But, if you make a change to

the unit such as the input or surround mode, the

display will show that change, then go back to off

after about 3 seconds. When changing the volume,

it is not displayed.

Display Off mode:

The display is off completely.

Note:

• Only the “DISP” indicator will be illuminated on the

front display in display off condition.

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source

selected for listening through this unit is sent to the

record outputs.

This means that any program you are watching

or listening to may be recorded simply by placing

machines connected to the outputs for TAPE OUT,

CD/CDR OUT and VCR OUT in the record mode.

To record the input source signal you are currently

watching or listening to

Select the input source to record by turning the

INPUT SELECTOR knob on the front panel or

simply press the input selector buttons on the

remote controller.

The input source is now selected and you may

watch or listen to it as desired.

The currently selected input source signal is

output to the TAPE OUT, CD/CDR OUT and

VCR OUT outputs for recording.

Start recording to the recording component as

desired.

Notes:

• When connecting only digital signal input, output

cannot be made to the TAPEOUT, CD/CDR OUT

or VCR OUT terminals. When using recording

functions, be sure to also make connections for

analog signal input.

• No conversion is made from Video signal input to

S-Video signal output or from S-Video signal input

to Video signal output. Always use the same signal

type for both input and output.

• Video or audio signals input to HDMI input terminals

cannot be recorded.

SELECTING ANALOG AUDIO INPUT OR DIGITAL

AUDIO INPUT

If you have already assigned the digital inputs, you

can temporarily select the audio input mode for each

input source as following procedures.

Press the AMP button and press the A/D button.

When this button is pressed, the input mode is

switched in the following sequence.

Auto → HDMI → Digital → Analog → Auto

Auto mode:

The types of signals being input to the digital and

analog input jacks for the selected input source are

detected automatically.

If no digital signal is being input, the analog input

jacks are selected automatically.

HDMI mode:

HDMI mode can be selected only when an HDMI

input has been assigned as an input source.

When “HDMI Audio” under Preference of the

Setup Menu is set to “Through”, the HDMI mode

cannot be selected.

Digital mode:

The input signal is ﬁ xed to an assigned digital input

terminal.

Analog mode:

The analog input jacks are selected.

This selection is temporary and will not be stored in

memory.

To store changes to the input mode, select “Input

Setup” from the Main Menu. (See page 27)

SR6003_U_01_ENG 3_4.indd 42SR6003_U_01_ENG 3_4.indd 42 08.8.1 1:08:02 PM08.8.1 1:08:02 PM

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 89 90

Comments to this Manuals

No comments

Marantz SR6003 User Manual Page 45

Comments to this Manuals

Related products and manuals for AV receivers Marantz SR6003