Marantz DV6200 Service Manual download pdf (Page 59)

2-7 2-8

DECK MECHANISM ADJUSTMENT

3. Adjustment Procedure

1. Insert Disc(Only Open/Close Key Pressing)

2. Wait Until the Sector Display is about 200,000 (Fig.11)

3. Adjust R-Skew adjusting Point until the Error rate has

Minimum rate with L-wrench (3mm).

4. Adjust T-Skew Adjusting Point until the Error rate has

Minimum rate.

5. Repeat No. 3, 4 adjusting procedure until the Error rate

have Minimum rate.

6. Error rate; SVC-3561 (ABEX) Disc=below 30 and

TDV-533 (ABEX) Disc=below 100. If not, Please

confirm Play ability on screen.

# You can watch the screen when pressing the Stop key

after the Adjusting is finished, Then perform Play and

Scan/Skip operation at Chapter1 and Chapter16 and

confirm screen condition, normal or abnormal.

R-SKEW ADJUSTING HOLE

T-SKEW ADJUSTING HOLE

Fig.12. Adjusting Method

Fig.11. Adjusting Screen Display

0045

SECTOR : 200145

0065

CURRENT PICK UP POSITION

ERROR RATE SIZE

ERROR RATE (HEXADEAMAL)

AVERAGE ERROR RATE

1. Reading upgrade disc

Connect the DVD Player to [TV] and Operate by using [Remote Controller]

1.1) Connect AC plug to mains power outlet.

1.2) Push OPEN/CLOSE

button , then open the disc tray. (Turned Power ON automatically)

1.3) Place the upgrade Disc on the disc tray and close the tray.

1.4) FTD indicates [ Press Up ] when Disc is acknowledged.

1.5) Push ARROW ( up )

button of Remote Controller .

1.6) FTD indicates [ READ 0 ]

If FTD indicated [ READ 1 ] or other number, please refer to 3. Error message.

1.7) FTD indicates [ UPGRADE 0 ] and begin to writing.

(Software writing into Flash ROM)

1.8) After few minutes, FTD indicate [ FINISHED ] and write completed.

(Software finished write into Flash ROM)

1.9) When upgrade is finished, open the tray automatically.

1.10) Remove the disc.

1.11) Push POWER

button and turn off the power.

2. Reset and MICOM version check

When upgrade is finished, the unit is should be resetting in order to finalize Upgrade.

The reset procedures are followings.

2.1) Push POWER

button.

2.2) Push SETUP

button.

2.3) Select “TV aspect”

2.4) Push ARROW( right )

button"

2.5) Push ARROW ( up )

button or ARROW ( down ) button and choose “16:9 wide”.

Attention : Do not push select/enter button ( Keep green triangle( > )mark )

If check mark is appeared, push arrow-right button and change to green triangle mark

2.6) Push “ Numeric button” in the following turn.

→

2.7) Push SELECT/ENTER

button.

The connected TV indicates “SYSTEM INFORMATION”

Please check “MICOM version”.

If other number indicate, need to retry this procedure again.

2.8) Push POWER

button and turn off the power.

Upgrade and Reset are success.

3. Error messege

During reading the upgrade disc, error messages are as follows

[Error Num] = 1 ~ 3

You can retry to upgrade by disc.

Because, flash ROM is not erased data yet.

[Error Num] = 4 ~

It is very worst case. The flash ROM is broken during erasing or programming.

You need to rewrite from hardware (PC) for using another jig.

SYSTEM INFORMATION

MODEL : DV6200/F1N

REGION-NO :2

CHIP-ID :PANTERA II

SERVO-VER :b003

MICOM-VER :V2.02 MP

PROM OPTION :XX XX XX XX XX XX

Factory Reset Done

Example indicated

How to upgrade by upgrade DISC. (*DV6200CDR)

1 2 ... 54 55 56 57 58 59 60

Comments to this Manuals

No comments

Marantz DV6200 Service Manual Page 59

Comments to this Manuals

Related products and manuals for DVD players Marantz DV6200