Marantz PMD510 Operations Instructions download pdf (Page 9)

CASCADE OPERATION

Cascade Operation is the ability to automatically and continuously

play or record both sides of a tape in Well A, both sides of a tape

in Well B, and then to automatically trigger a second machine, and

continuously play or record on both sides of both tapes in machine

number two. In fact, many machines can be wired in cascade mode

for virtually limitless continuous recording/playback capability.

Cascade mode connections consist of a signal RCA cable which

runs from the EXTENSION REMOTE F output jack on the rear panel

of the first machine, to the EXTENSION REMOTE F input jack on

the rear panel of the next machine. See figure 3 for details.

CASCADE CONTINUOUS PLAYBACK

1. Insert all cassettes (rewound), set Dolby NR, and set all reverse

mode switches to

modes.

2. Press the CONT. 6 buttons on all units.

3. Press the PLAY 5 4 button of Well A, of Unit #1.

4. When Well A of Unit #1 finishes, Well B of Unit #1 will start

automatically.

5. When Well B of Unit #1 finishes, Well A of Unit #2 will start

automatically.

6. To stop playback, press the CONT. 6 button, and STOP buttons

on all units.

Note: Output from both wells of each unit will be sent to LINE

Output A on each unit. Line Output B is not used on any unit.

CASCADE CONTINUOUS RECORDING

1. Insert all cassettes (rewound), set Dolby NR, and set all reverse

mode switches to

mode.

2. Press the CONT. 6 buttons of all units.

3. Press the REC 4 buttons on both wells of each unit. Check to see

that every well indicates REC-PAUSE mode.

4. Adjust the recording level of each well.

5. Press the PLAY 5 4 button on Well A of Unit #1.

6. When well A of Unit #1 finishes, Well B of Unit #1 will start

automatically.

7. When well B of Unit #1 finishes, Well A of Unit #2 will start

automatically.

8. To stop recording, press the CONT. 6 button and STOP buttons

on all units.

Note: Input to both wells of each unit will be received from Line

Input A on each unit. Line Input B is not used on any unit.

CD SYNCHRO RECORDING

(When connected to a Marantz Professional CD

player.)

The CD Synchro Recording is possible only when this unit is

connected with a Marantz Professional CD player equipped with

the Sync Recording function.

The CD Synchoro Recording connection consists of a single RCA

cable which runs to the RC-5 REMOTE E input jack on the rear panel

of the PMD510, from the REMOTE output jack on the rear panel of

the Marantz CD player.

1. Insert all cassettes (rewound), set Dolby NR, and set reverse

mode switch to either

or mode (not mode).

2. Press the REC 4 button on Well of the unit. Check to see that REC-

PAUSE mode is indicated.

3. Adjust the recording level with CD playing.

4. Set reverse mode switch to

mode.

5. Press the play button of the CD player.

6. The tape recording will When the CD starts playing, and stop

when the CD player stops playback.

7. When recording two tapes in parallel, press the A+B REC 5

button insted of the REC button.

OTHER OPERATIONS

Caution:

• If you must stop playback or recording in the middle of a tape,

be sure to press the STOP - button first, then turn the power off.

If the power is turned off in the middle of an operation, the

cassette tape remains loaded, and it may be impossible to eject.

In such a case, turn the power on, enter PLAY mode, then press

STOP, and then eject the tape.

• The same coution as above also applies in cases of power

failure. To prevent damage, never attempt to force the removal

of a cassette while the power is off.

ERASURE OF TAPE

When a program source is recorded onto a tape, the previously

recorded sound is erased automatically, and replaced with the new

recording. If you wish to erase a tape without recording, set the

REC LEVEL control to the minimum (0) position, and let the tape

travel in the REC mode.

AUTO TAPE SELECTOR

This unit is equipped with an auto tape selector whitch automati-

cally sets the bias and equalizer level using the detection holes

provided in the cassette shell. The bias and equalizer levels are

automatically set according to the type of cassette as follows. (See

Figure 4)

• Normal tapes EQ;120mS, Bias; Low

• CrO2 tapes EQ; 70mS, Bias; High

• Metal tapes EQ; 70mS, Bias; Metal

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Marantz PMD510 Operations Instructions Page 9

Comments to this Manuals

Related products and manuals for Cassette players Marantz PMD510