Marantz NR1403U User Manual download pdf (Page 64)

100

101

Audyssey

Default settings are underlined.

Set Audyssey MultEQ

, Audyssey Dynamic EQ

and Audyssey Dynamic Volume

. These can be

selected after Audyssey

Setup has been performed. For additional information on Audyssey technology,

please see page89.

NOTE

•If you have not performed Audyssey

Setup, or if you change the speaker settings after performing

Audyssey

Setup, you may not be able to select Dynamic EQ

/Dynamic Volume

In this case, either perform Audyssey

Setup over again or perform “Restore...” (vpage 27) to

return to the settings after Audyssey

Setup was run.

•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”

cannot be set.

Setting items Setting details

MultEQ

compensates for

both time and frequency

characteristics of the

listening area based on

Audyssey

Setup

measurement results.

Selection is done from three

types of compensation

curves. We recommend the

“Audyssey” setting.

MultEQ

is the prerequisite

function for Dynamic EQ

and Dynamic Volume

Audyssey : Optimize the frequency response of all speakers.

Audyssey Byp.L/R : Optimize frequency response of speakers except

front L and R speakers.

Audyssey Flat : Optimize frequency response of all speakers to ﬂat

response.

Manual EQ : Apply frequency response set with “Manual EQ”

(vpage63).

Off : Turn “MultEQ

” equalizer off.

•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be

selected after Audyssey

Setup has been performed. “Audyssey”

is automatically selected after performing Audyssey

Setup. When

“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,

illuminates.

•After running Audyssey

Setup, if the Speaker Conﬁguration, Distance,

Channel Level, and Crossover Frequency have changed without

increasing the number of speakers measured, only illuminates.

•This can also be set by pressing

MultEQ.

Each time MultEQ is pressed, the setting is

changed as shown below.

Audyssey Audyssey Byp.L/R

Audyssey FlatManual EQOff

NOTE

When using headphones, “MultEQ

” is automatically set to “Off”.

“MultEQ

”, “Dynamic EQ

” and “Dynamic Volume

” settings are stored for each input source.

Audio

Audio Delay

Default settings are underlined.

While viewing video, manually adjust the time to delay audio output.

Setting details

0ms – 200ms

•This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” (vpage65) is set to

“On” and when a TV compatible with Auto Lip Sync is connected.

•Store “Audio Delay” for each input source.

Volume

Default settings are underlined.

Set the volume setting.

Setting items Setting details

Scale

Set how volume is

displayed.

0 – 98 : Display in the range 0.5 (Min) to 98.

–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.

The “Scale” setting is applied also to the “Limit” and “Power On

Level” display method.

Limit

Make a setting for

maximum volume.

Off : Do not set a maximum volume.

60 (–20dB) / 70 (–10dB) / 80 (0dB)

Power On Level

Deﬁne the volume setting

that is active when the

power is turned on.

Last : Use the memorized setting from the last session.

Mute : Always use the muting on condition when power is turned on.

1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.

Mute Level

Set the amount of

attenuation when muting

is on.

Full : The sound is muted entirely.

–40dB : The sound is attenuated by 40 dB down.

–20dB : The sound is attenuated by 20 dB down.

Basic version

Advanced version

Informations

Advanced version

v See overleaf

DVD

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 100 101

Comments to this Manuals

No comments

Marantz NR1403U User Manual Page 64

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Marantz NR1403U