11
ENGLISH
BASIC OPERATION
OPERATION PROCEDURES
Operate each equipment to start play.
7
To play an analog disc
1. Set the INPUT SELECTOR switch q to
PHONO.
2. Play a disc on the turntable.
3. Adjust the volume with the VOLUME control
w and adjust the tone with the BASS and
TREBLE controls e.
NOTES:
• Set the VOLUME control to the minimum
position before placing the stylus on the disc or
before replacing the cartridge.
• Do not apply shock or vibration to the turntable
during play, as this may cause the stylus to jump
and the analog disk to be damaged.
• If the turntable is installed too close to the
speakers, the volume may not be able to be
increased to a high level due to howling.
• Do not switch the power OFF while the stylus is
on the disc surface.
7
To listen to FM/AM broadcasts
1. Set the INPUT SELECTOR switch q to
TUNER.
2. Tune in the desired station on the tuner.
3. Adjust the volume with the VOLUME control
w and adjust the tone with the BASS and
TREBLE controls e.
7
To play a CD
1. Set the INPUT SELECTOR switch q to CD.
2. Play a CD on the CD player.
3. Adjust the volume with the VOLUME control
w and adjust the tone with the BASS and
TREBLE controls e.
7
To play a DVD or component
connected to AUX/DVD jacks
The component connected to the AUX/DVD jacks
on the rear panel can be played as follows.
1. Set the INPUT SELECTOR switch q to AUX/
DVD.
2. Play the component connected to the selected
input.
3. Adjust the volume with the VOLUME control
w and adjust the tone with the BASS and
TREBLE controls e.
RECORDER OPERATION
Control used for operating the tape deck.
7
PLAYBACK
1. Set the INPUT SELECTOR switch A to
RECORDER 1 (CD-R) or RECORDER 2 (MD/
TAPE).
2. Play a prerecorded disc or tape on the
recorder.
3. Adjust the volume with the VOLUME control
B.
4. Adjust the tone with the BASS and TREBLE
controls C.
7
RECORDING
The playback sound of a program source component,
such as a turntable, a tuner, or a CD player, can be
recorded on disc or tape as followss.
1. Set the REC SELECTOR switch to the program
source to be recorded.
2. Play the program source.
3. Operate the recorder(s) to record the playback
sound on disc(s) or tape(s).
7
Using REC SELECTOR switch
The REC SELECTOR switch is used when copying
a recorded disc or tape to another disc or tape, or
recording a CD onto a recordable disc or cassette
tape.
1. When the switch is in the OFF position, the
signal is not output at the REC OUT jacks.
It is not necessary to output the signal at the
REC OUT jacks when the signal is not recorded
onto disc or tape.
By setting the switch to OFF, the signal path
inside the unit can be shortened and crosstalk,
etc., can be reduced.
2. In the SOURCE position, the signal selected
with the INPUT SELECTOR switch can be
recorded onto disc/tape.
3. In the COPY positions, the RECORDER 2 (MD/
TAPE) signal can be recorded onto RECORDER
1 (CD-R) or vice versa.
4. In the COPY position, the program source
selected with the INPUT SELECTOR switch
can be monitored through the speakers.
REC SELECTOR
PM6002N_01_ENG.indd 11PM6002N_01_ENG.indd 11 07.7.18 9:56:15 AM07.7.18 9:56:15 AM
(38 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals