Marantz PM6002 User Manual download pdf (Page 16)

ENGLISH

TROUBLESHOOTING

In case of trouble or abnormal operation of the unit, check the following before contacting service personnel.

What may seem to be a serious malfunction is often the result of a simple operation mistake. If the trouble

persists after checking the following, please contact your dealer or nearest Marantz distributor.

* The ampliﬁ er does not operate and the

indicators do not light.

1. Check to see if the power cord is inserted

properly into the power outlet.

* The indicators light but the ampliﬁ er does

not operate.

1. Check to see if the SELECTOR, SPEAKER

switches and VOLUME control are properly

set.

* Sound is heard from only one of the

speakers.

1. Check to see if the BALANCE control is

properly set.

2. Switch the power of the unit to OFF, and change

the connections of the left and right speaker

cords. If the sound from the same speaker is still

not heard, its connection cord or the speaker

itself may be defective.

* Considerable hum noise is heard when

the turntable is played.

1. Check to see if the plugs from the turntable are

properly connected to the PHONO jacks.

2. Connect the grounding wire of the turntable to

the GND terminal on the rear panel of this unit.

If it has already been connected, try removing

it.

3. Check to make sure that the phono cartridge is

attached securely to the tonearm.

4. Unplug the power cord and plug it in again after

inverting the orientation of the blades.

Remote control operation is not possible.

1. Is the remote controller's transmitter pointed

correctly at the remote sensor on the front of the

Amplifier?

Or, is there an obstruction between the

transmitter and the remote sensor?

2. Are the batteries in the remote controller

exhausted?

3. Is there another strong light (from a window,

etc.) striking the Amplifier remote sensor?

4. Is an RCA cord connected to the “REMOTE

CONTROL OUT” jack on the Amplifier rear

panel?

OTHERS

The section describes the care and maintenance

tasks that must be performed to optimize the

operation of your Marantz equipment.

Cleaning of equipment external

surfaces

The exterior finish of your unit will last indefinitely

with proper care and cleaning, Never use scouring

pads, steel wool, scourging powders or harsh

chemical agents (e.g., lye solution), alcohol, thinner,

benzine, insecticide or other volatile substances as

these wil mar the finish of the equipment. Likewise,

never use cloths containing chemical substances. If

the equipment get dirty, wipe the external surfaces

with a soft, lint-free cloth.

If the equipment becomes heavily soiled:

• dilute some washing up liquid in water, in a ratio

of one part detergent to six parts water.

• dip a soft, lint free in the solution and wring the it

is damp.

• wipe the equipment with the damp cloth.

• dry the equipment by wiping it with a dry cloth.

Repairs

Only the most competent and qualified service

technicians should be allowed to service the

factory-trained warranty station personnel have

the knowledge and special facilities needed for

repair and calibration of this precision equipment.

After the warranty period has expired, repairs will

be performed for a charge if the equipment can be

returned to normal operation.

In the event of difficulty, refer to your dealer or write

directly to the nearest location to you that is listed

on the Marantz Authorized Service Station list. If

writing, please include the model and serial number

of the equipment together with a full description of

what you think is abnormal about the equipment's

behaviour.

PM6002N_01_ENG.indd 12PM6002N_01_ENG.indd 12 07.7.18 9:56:15 AM07.7.18 9:56:15 AM

1 2 ... 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments

Marantz PM6002 User Manual Page 16

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Marantz PM6002