Marantz SR7500 User Manual download pdf (Page 23)

ENGLISH

Select 2. SPEAKER SETUP on the SETUP

MAIN MENU, then select MANUAL for 2-1

SPEAKER SETUP.

To select the each speaker, press the or

cursor buttons.

To select the setting of each speaker size,

press the or cursor buttons.

After you complete this portion of the set up,

move the cursor to “NEXT” with the or

cursor buttons and then press the ENTER

button to go to the next page.

THX SPEAKER SYSTEM

If you use full THX speaker systems which are

approved by THX Ltd. the front, the center and

surround speaker size should be ”Small” and the

subwoofer should be “Yes”.

You need to set number of surround back speaker

only.

SUBWOOFER

YES:

Select when a subwoofer is connected.

NONE:

Select when a subwoofer is not connected.

FRONT L/R

LARGE:

Select if the front speakers are large.

SMALL:

Select if the front speakers are small.

• If “NONE” is selected for the Subwoofer setting,

then this setting is fixed to “LARGE.”

CENTER

NONE:

Select if no center speaker is connected.

LARGE:

Select if the center speaker is large.

SMALL:

Select if the center speaker is small.

SURROUND L/R

NONE:

Select if no surround left and right speakers are

connected.

LARGE:

Select if the surround left and right speakers are

large.

SMALL:

Select if the surround left and right speakers are

small.

1 INPUT SETUP

(ASSIGNABLE DIGITAL INPUT)

6 digital inputs can be assigned to a desired

source.

With the SR8500, DVI-D input can be assigned to

a preferred source.

Use this menu to select the digital input jack to be

assigned to the input source.

Select “INPUT SETUP” in SETUP MAIN

MENU with or cursor button, and press

the ENTER button.

To select the input source, press the or

cursor buttons.

To select the digital input jack, press the or

cursor buttons.

Select “Dx-AT” for input sources, for automatic

detection of the digital input signal condition.

If there is not a digital signal present, but there

is an analog signal present, the analog signal

will be played.

Select “Dig x”, when only a digital signal will be

used.

Select “ANA” for input sources for which

no digital input jacks are used.

To select the video source, select “DVI1” or

“DVI2” by pressing the or cursor buttons,

and press the or cursor buttons to select

the video source to be assigned .(SR8500

only)

After you complete this portion of the set up,

move the cursor to MAIN with the or

cursor buttons and press the ENTER button.

Notes:

• The TUNER and AUX2 are fixed to the analog

input, and cannot be selected for any digital input.

• When a DTS-LD or DTS-CD is playing, this setup

is not available. This is to avoid noise being

generated from the analog input.

• If “Dx-AT” is selected and a DVD, compact disc

or LD is fast-forwarded during playback, decoded

signals may produce a skipping sound. In such

cases, change the setting to DIGITAL.

2 SPEAKER SETUP

After you have installed the SR7500, connected all

the components, and determined the speaker

layout, it is now time to perform the settings in the

Speaker Setup menu for the optimum sound

acoustics for your environment and speaker

layout.

Before you perform the following settings, it is

important that you first determine the following

characteristics:

2-1 SPEAKER SETUP

Speakers are set up by selecting either MANUAL

or AUTO using the and cursor buttons. For

operation when AUTO has been selected, see

MRAC on page 21.

2-2 SPEAKERS SIZE

When setting the speaker size in the SPEAKER

SIZE sub-menu, use the guidelines given below.

LARGE:

The complete frequency range for the channel

you are setting will be output from the speaker.

SMALL:

Frequencies of the channel you are setting

lower than approx. 100 Hz will be output from

the subwoofer.

If the Subwoofer is set to “NONE” and the front

speakers are set to “LARGE,” then the sound

will be output from both the left and right

speakers.

SURR. BACK

NONE:

Select if no surround back left and right

speakers are connected.

2CH:

Select if the surround back left and right

speakers are connected.

1CH:

Select if the one surround back speaker is

connected.

In this case, the audio signal is emitted form the

Surround L output terminal.

Notes:

• If “NONE” is selected for the Surround L/R

setting, then this setting is fixed to “NONE.”

• You can use surround back speaker terminals as

multi room speaker terminals when you use no

surround back speaker. (See page 17)

SURR. BACK SIZE

LARGE:

Select if the surround back speaker is large.

SMALL:

Select if the surround back speaker is small.

Note:

• If “NONE” is selected for the Surround L/R

setting, then this setting is not available.

LPF/HPF

When you use a subwoofer, you can select the

cutoff frequency for the small speakers used.

Select one of the crossover frequency levels

according to the size of the small speaker

connected.

80Hz:

Select this when the bass speaker is about 12

cm (4 3/4 inches).

100Hz:

Select this when the bass speaker is about 10

cm (3 15/16 inches).

120Hz:

Select this when the bass speaker is about 8 cm

(3 3/16 inches).

Notes:

• Use the above comments as reference when

adjusting.

• If Pure-Direct mode, 7.1CH Input is in use, this

function does not take effect.

2-2 SPEAKERS SIZE

SUBWOOFER : YES

FRONT L /R : SMALL

CENTER : SMALL

SURROUND L / R : SMALL

SURR . BACK : 1CH

SURR . BACK S I ZE : SMAL L

LPF /HPF : 100 HZ

BASS M I X : BOTH

MA I N RETURN NEXT EX I T

2 - 1 SPEAKER SETUP

SPEAKERS SETUP : MANUAL

MA I N NE X T EX I T

1INPUTSETUP

CD : D6 -AT DV I 1 : DVD

TAPE :ANA DV I 2 :DSS

CD - R : D1 - AT

TV :D4 -AT

DVD : D5 - AT

VCR1 : ANA

DSS : D2 - AT

AUX1 : D - AT

MA I N E X I T

SR8500 only

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 57 58

Comments to this Manuals

No comments

Marantz SR7500 User Manual Page 23

Comments to this Manuals

Related products and manuals for Acoustics Marantz SR7500