Marantz SR8002 User Manual download pdf (Page 62)

ENGLISH

(Using the remote controller)

When switching to M-DAX mode, press the AMP

button and then the > button until the PAGE 4 is

displayed.

When “M-DAX” is displayed on the remote controller,

press the M-DAX (D5) button.

Each time this button is pressed, M-DAX changes

as follows.

OFF LOW HIG

Notes:

• M-DAX is compatible with PCM (48 kHz or lower)

and two-channel analog sources.

• The M-DAX is not available when Dolby Virtual

Speaker mode is being used.

VIDEO CONVERT

ANALOG VIDEO CONVERSION

This unit is equipped to convert video signals

for monitor output. Because of this, indifferent of

the connection (VIDEO, S-VIDEO, COMPONENT

VIDEO) between the playback device and this unit,

listening and viewing are possible with a single

higher grade cable between the MONITOR OUT

terminal of the unit and the monitor.

UP-CONVERSION FROM ANALOG VIDEO

SIGNALS TO HDMI

The up-conversion feature of this unit can output

the input analog video signals (for component video

signals of 480i, 480p, 1080i and 720p resolution, and

S-Video and Video (composite) of 480i resolution) to

the HDMI MONITOR terminal.

Notes:

• HDMI video input is only output to the HDMI

MONITOR OUT terminal of the unit. If connecting

a playback device such as a DVD player to the

HDMI input jack, connect the HDMI MONITOR

OUT terminal of the unit to a TV monitor.

• This mode is unavailable for the REC out terminal.

• This mode is unavailable for still picture, fast

forward and reverse play on video component.

•

If, while attempting to use the video convert

feature, the unit cannot synchronize with the

display device, “NO SIGNAL” appears on the

monitor or noise is generated, this feature cannot

be used. All of these signs are caused by equipment

incompatibility; there is nothing wrong with the unit.

If this occurs, set “VIDEO CONVERT” in the

“VIDEO SETUP” menu to “DISABLE”. Next,

connect the video input signal to the display component

via the MONITOR OUT terminal under VIDEO and

the S-video input signal to the display component via

the MONITOR OUT terminal under S-VIDEO.

• The video convert feature constantly monitors

input video signals and determines whether to

convert the input signals or not. However, some

input video signals cannot be detected correctly.

If this occurs, set “VIDEO CONVERT” in the

“VIDEO SETUP” menu to “DISABLE”.

•

For optimal video performance, THX recommends

setting the “VIDEO CONVERT” mode “DISABLE”.

CONNECTION EXAMPLE

• When a monitor is connected to the HDMI

MONITOR OUT terminal of the unit

DIGITAL

RLVIDEO

S-VIDEO

AUX 1 INPUT

AUDIO

VOLUME

DOWN

STANDBY

PHONES

INPUT SELECTOR

AV SURROUND RECEIVER SR8002

M-DAX

ENTER

PURE DIRECT THX

7.1CH INPUT

MODE AUTO

MULTI

A/B

T-MODE

MEMORY CLEAR

DISPLAY

EXIT

SPEAKERS

BAND

MIC

PURE DIRECT

SURROUND

SPEAKER

MULTI

DSD

POWER ON/OFF

VIDEO

or S-VIDEO

or component

HDMI

or HDMI

Notes:

• If the resolution of the component video signal

input from the playback device is other than 480i,

480p, 1080i or 720p, images are not output from the

HDMI MONITOR OUT terminal of the unit.

• If the resolution of the S-Video or Video signal input

from the playback device is other than 480i, images

are not output from the HDMI MONITOR OUT

terminal of the unit.

• When a monitor is connected to the VIDEO or S-

VIDEO MONITOR OUT terminals of the unit

DIGITAL

RLVIDEO

S-VIDEO

AUX 1 INPUT

AUDIO

VOLUME

DOWN

STANDBY

PHONES

INPUT SELECTOR

AV SURROUND RECEIVER SR8002

M-DAX

ENTER

PURE DIRECT THX

7.1CH INPUT

MODE AUTO

MULTI

A/B

T-MODE

MEMORY CLEAR

DISPLAY

EXIT

SPEAKERS

BAND

MIC

PURE DIRECT

SURROUND

SPEAKER

MULTI

DSD

POWER ON/OFF

SL S SR

LFE

DIGITAL

SURROUND

V-OFFDISP MULTI AUT O TUNED STSPKR A B

NIGHT

PEAK ANALOG

DIGITAL

ATT

SLEEP

SURR DIRECT

AUTO

DISC 6.1 MTX 6.1 EQ

PCM

AAC

VIDEO

or S-VIDEO

VIDEO

or S-VIDEO

or component

HDMI

ADJUSTING THE TONE (BASS & TREBLE)

CONTROL

AMP

AUX2

AUX1

TAPE

TUNER

CD-R

LIGHT

Learning Remote Controller

RC8001SR

AMP

VOL

LEARN

NAME

MACRO

USE

PAGE

123

During a listening session you may wish to adjust the

Bass and Treble Control to suit your listening tastes

or room acoustics.

(Using the remote controller)

adjust the tone

, press the AMP button and press

the > button PAGE3 is displayed.

To adjust the bass effect, press BASS+ (D2) or

BASS– (D3).

To adjust the treble effect, TREB+ (D4) or TREB–

(D5).

Notes:

• The tone control function is unavailable for the

Source Direct, Pure Direct, Headphone, Dolby

Virtual Speaker, THX mode, and 176.4/192kHz

PCM.

• The tone control function is not available when

ACOUSTIC EQ is being used.

• Additionally, tone control is not available during

Dolby TrueHD, Dolby Digital Plus, or DTS-HD

playback.

TEMPORARILY TURNING OFF THE SOUND

2 31

5 64

8 97

MUTE

EXIT

GUIDE

TEST

CH.SEL

LIP.SYNC

SURR

7.1CH

ATT

SPK-AB

DISP

OSD

SLEEP

MUTE

To temporarily silence all speaker outputs such as

when interrupted by a phone call, press the MUTE

button on the remote controller.

This will interrupt the output to all speakers and the

head-phone jack, but it will not affect any recording or

dubbing that may be in progress.

When the system is muted, the display will show

“MUTE” .

Press the MUTE button again to return to normal

operation.

USING THE SLEEP TIMER

2 31

5 64

MEMO

CLEAR

MUTE

EXIT

GUIDE

TEST

CH.SEL

LIP.SYNC

SURR

7.1CH

ATT

SPK-AB

DISP

OSD

THX

SLEEP

To program this unit for automatic standby, press the

SLEEP button on the remote controller.

Each press of the button will increase the time before

shut down in the following sequence.

OFF 10 20 30 5040

100 90 80 70 60110120

The sleep time will be shown for a few seconds in the

display on the front panel, and it will count down until

the time has elapsed.

When the programmed sleep time has elapsed, the

unit will automatically turn off.

Note that the SLEEP indicator on the display will

illuminate when the Sleep function is programmed.

To cancel the Sleep function, press the SLEEP

button until the display shows “SLEEP OFF” and the

SLEEP indicator will disappear.

M-DAX (Marantz Dynamic Audio eXpander)

AMP

AUX2

AUX1

TAPE

TUNER

CD-R

LIGHT

Learning Remote Controller

RC8001SR

AMP

VOL

USE

PAGE

This function makes up for lost audio content in MP3

or AAC sources (from lossy compression) during

playback. Choose one of the following levels for this

effect as desired.

“HIGH”: Stronger effect

“LOW”: Weaker effect

“OFF”: Deactivated.

SR7002-8002_U_01_ENG 3_3.indd 59SR7002-8002_U_01_ENG 3_3.indd 59 07.8.24 1:15:59 PM07.8.24 1:15:59 PM

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 93 94

Comments to this Manuals

No comments

Marantz SR8002 User Manual Page 62

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Marantz SR8002