Marantz SR8002 User Manual Page 84
- Page / 94
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
81
ENGLISH
HDMI
SYMPTOM CAUSE REMEDY
The display does not
appear over an HDMI
connection.
The connected monitor or projector
does not support HDCP.
The HDMI input of on the TV is
not on.
Set HDMI input so that it turns on, as
explained in the TV's instruction manual.
The HDMI output on the source
component (DVD, Set Top Box,
etc.) is not on.
Set HDMI output so that it turns on, as
explained in the source component's
instruction manual.
The HDMI mode is not correctly
set on the unit.
Set HDMI input on the FUNC INPUT
SETUP menu as explained on page 43.
The HDMI output video resolution
of the source component (DVD,
Set Top Box, etc.) does not match
the TV specifi cations.
Set the resolution so that it matches, as
explained in the instruction manuals of both
components.
The device is connected with a
non-standard HDMI cable.
A 5 m or shorter cable is recommended to
ensure stable operation and prevent image
quality deterioration.
Power to the unit is off. (When
the unit is on standby, HDMI
connections cannot be turned
on.)
Turn on the power to the unit.
The connection between
HDMI components was not
authenticated.
Shut off and then turn the power back on to
the unit, TV and source component.
Time is needed for the
display of an HDMI
connection to appear.
The connection is being
authenticated between the HDMI
devices.
There is nothing wrong with the system.
Some HDMI devices require time for
authentication.
Audio is not played
back over an HDMI
connection.
The HDMI audio output of the
source component (DVD, Set Top
Box, etc.) is not on.
Set the HDMI audio output so that it turns
on, as explained in the source component's
instruction manual.
The signal format of the source
component (DVD, Set Top Box,
etc.) is not supported by the unit.
Set the HDMI audio output so that it can
connect to the unit, as explained in the
source component's instruction manual.
This unit is set to the HDMI audio
“THROUGH” mode.
In the “THROUGH” mode, sound is not
produced from the unit. Set it to “ENABLE”.
(see page 54)
DVD-Audio is not played
back over an HDMI
connection.
The DVD player does not support
CPPM, therefore it cannot output
HDMI audio.
• Use a DVD-Audio player that supports
CPPM.
• Turn on PCM downsampling on the DVD
player.
• Use an analog connection.
XM SATELLITE RADIO
If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there
may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM CAUSE REMEDY
“ANTENNA” is displayed. XM terminal and the XM Mini-Tuner and
Home Dock is not properly connected.
Check that the connection are correct.
“NO SIGNAL” is displayed. The signal cannot be received. Reposition your XM Mini-Tuner and Home
Dock.
Receiving only XM channels 0 and 1. The XM Tuner is not activated. Contact XM Radio.
PROTECTIVE FEATURE
In some cases, the STANDBY indicator may blink slowly, twice per second. In this case, turn off the unit, unplug
the power cord, and check the following points.
• Make sure the speaker cables are not reversed and connected to the wrong sides (+ and -) on the unit.
• Make sure the speaker cables connected to the unit are not shorted. (Check both the unit end and the speaker
end.)
• Make sure the volume does not exceed the level that the unit is capable of producing.
• When using the unit in a rack or other enclosed space, heat may build up inside the unit and cause a fi re. When
installing the unit, be sure to leave suffi cient space between the top, back and both sides of the unit and walls or
other AV components to prevent the internal temperature from rising.
After checking these points, plug in the power cord and use the remote controller to turn on the unit. Turn down
the volume before resuming playback. Confi rm that there are no problems with the speaker connections and
playback performance.
If this symptom recurs, request service at your nearest service center.
In rare instances, the unit may enter standby mode and the STANDBY indicator may blink rapidly, 8 times per
second. In this case, unplug the power cord and request service at your nearest service center.
HD Radio RECEPTION
SYMPTOM CAUSE REMEDY
The signal is not digital, even when
receiving from an HD Radio station.
(SR8002 only)
Reception is affected by other electrical
fi elds. (AM)
Try changing location where the AM
indoor antenna is set up.
The radio waves from the broadcasting
station are weak. (FM)
Install an FM outdoor antenna.
The signal sometimes switches from
digital to analog or the sound cuts out
when receiving from an HD Radio station.
(SR8002 only)
Reception is affected by other electrical
fi elds. (AM)
Set the TUNER MODE to Analog Auto
mode or Analog Mono mode.
Note:
In this case you cannot receive a
digital signal. (See page.70)
The radio waves from the broadcasting
station are weak. (FM)
SR7002-8002_U_01_ENG 3_3.indd 81SR7002-8002_U_01_ENG 3_3.indd 81 07.8.24 1:16:15 PM07.8.24 1:16:15 PM
- AV Surround Receiver 1
- IMPORTANT SAFETY 2
- INSTRUCTIONS 2
- DECLARATION OF CONFORMITY 3
- INTRODUCTION 4
- TABLE OF CONTENTS 5
- FEATURES 5
- DESCRIPTION 6
- BEFORE USE 9
- REMOTE CONTROL 10
- LOADING BATTERIES 10
- CAUTIONS ON BATTERIES 10
- NAMES AND FUNCTION 11
- SURROUND 12
- REAR PANEL 13
- OPERATION (RC8001SR) 14
- SETTING THE TIME 16
- Learning Remote Controller 17
- RC8001SR 17
- BASIC OPERATION 20
- ERASING PROGRAMMED CODES 22
- Erasing Direct Button Pages 22
- Erasing Sources 22
- PROGRAMMING MACROS 23
- CLEARING MACRO PROGRAMS 24
- CLONE MODE 25
- SETTING THE LIGHTING TIME 26
- OPERATION (RC101) 27
- CONTROLLING A MARANTZ TV (TV) 28
- LEARN MODE 32
- LEARNING PROCEDURE 32
- INITIAL SETTINGS) 32
- OTHER OPERATIONS 33
- CONNECTIONS 34
- CONNECTING AUDIO COMPONENTS 35
- CONNECTING VIDEO COMPONENTS 36
- HDMI OUTPUT HDMI INPUT 37
- HDMI OUTPUT 37
- ADVANCED CONNECTING 38
- FM ( 575 )) GNDGND AMAM 39
- ANTANTENNA 39
- XM RADIO OVERVIEW 40
- CONNECTING FOR THE MULTI ROOM 41
- MULTIROOM B 41
- MULTIROOM A 41
- CONNECTING OTHER EQUIPMENT 42
- RC8001SR BUTTON CONTROL 43
- 1 INPUT SETUP 45
- 1-1 FUNC INPUT SETUP 46
- (ASSIGNABLE DIGITAL INPUT) 46
- 1-2 7.1 CH INPUT SETUP 46
- 1-3 FUNCTION RENAME 47
- 2 SPKR (SPEAKER) SETUP 48
- AV SURROUND RECEIVER SR8002 49
- ERROR MESSAGES 51
- 2-2 MANUAL SETUP 52
- <SPEAKER SIZE> 52
- <SPEAKER DISTANCE> 52
- <SPEAKER LEVEL> 53
- 2-3 THX AUDIO SETUP 53
- 3 SURROUND SETUP 54
- 4 VIDEO SETUP 56
- 5 PREFERENCE 57
- 5-1 MULTI ROOM SETUP 58
- 5-2 DC TRIGGER SETUP 58
- 6 ACOUSTIC EQ 59
- 6-2 CHECK AUTO 60
- 6-1 PRESET G. EQ ADJ 60
- ANALOG VIDEO CONVERSION 62
- SIGNALS TO HDMI 62
- CONNECTION EXAMPLE 62
- SURROUND MODE 63
- OTHER FUNCTION 67
- DOLBY HEADPHONE MODE 68
- SPEAKER A/B 68
- 7.1 CH INPUT 68
- AUX2 INPUT 69
- VIDEO ON/OFF 69
- TV AUTO ON/OFF FUNCTION 69
- LIP.SYNC 69
- DUAL BACKUP MEMORY 69
- PRESET MEMORY 71
- PRESET CHANNEL LIST DISPLAY 72
- RECALLING A PRESET STATION 72
- PRESET SCAN 72
- SORTING PRESET STATIONS 72
- (SR8002 ONLY) 73
- SELECTING MULTICAST CHANNELS 75
- FM WXYZ-FM 2 75
- PTY AUTO SEARCH 75
- RBDS OPERATION (SR8002 ONLY) 76
- SEARCH MODE 78
- NEURAL SURROUND MODE 80
- MULTI ROOM 81
- (RC101) FOR MULTIROOM A 82
- (RC101) FOR MULTIROOM B 82
- TROUBLESHOOTING 83
- XM SATELLITE RADIO 84
- HD Radio RECEPTION 84
- TECHNICAL SPECIFICATIONS 85
- SETUP CODES 86
- (RC8001SR) 86
- Source button name : TV 88
- Source button name : VCR 89
- Source button name : DVD 90
- DIRECT BUTTON 91
- FUNCTIONS (RC8001SR) 91
Related products and manuals for Receivers and Amplifiers Marantz SR8002
(47 pages)
(33 pages)
(18 pages)© 2020, manymanuals.com. All rights reserved. | 1.583 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals