Marantz SR7500 User Manual download pdf (Page 43)

ENGLISH

BASIC OPERATION

USE MODE

(Normal operation status)

This remote control is preset with a total of 12

types of remote codes, including Marantz TV

(television), DVD, VCR (VCR deck), DSS (satellite

broadcasting tuner), TUNER, CD, CD-R, MD,

TAPE (tape deck), AUX1, AUX2, and AMP

(amplifier).

Learning is not necessary for Marantz products.

You can use these products without setting any

codes.

Press the SOURCE button.

For this example, press DVD.

DVD is shown on the LCD, and the remote control is

set for DVD.

Pressing the source button once changes the remote

control to the settings for the source that was

pressed.

To change the amplifier or other source, press the

SOURCE button twice (double-click). The code is

sent, and then the amplifier source changes to DVD.

Press the buttons to operate the DVD.

The indicator is shown on the LCD while the

remote control codes are being transmitted. It is not

displayed when buttons without stored code are

pressed.

The direct buttons can be used to perform up

to 20 operations for each of the 12 sources,

including DVD, TV, AMP, and other AV

equipment.

The buttons consist of the D1 to D5 buttons, and the

equipment is operated by pressing the buttons

corresponding to the indicators on the LCD.

Four pages are available, and press the > button to

select a page. The current page position is displayed

on the LCD.

PRESET MODE

(When operating non-Marantz AV equipment

products)

This remote control is preset with remote control

codes from AV equipment by other manufacturers.

The preset codes are TV, VCR, LD, CABLE, DSS,

DVD, TAPE, TUNER, CD, CD-R, MD and AMP.

Settings can be made in one of two ways.

When the preset codes are set, the following

codes are contained in the source button of the

remote control.

See the attached manufacturer number list for the

preset manufacturers, devices, preset numbers,

and other settings.

• When using Marantz products, TV and DVD can

be set to TV1 (TV/VDP: Projector) and TV2

(PDP: Plasma display), and DVD1 (first DVD

player) and DVD2 (second DVD player),

respectively, to match the customer’s operating

environment. These settings are made in

PRESET mode.

In the factory default state, the remote control is

set to TV1 and DVD1. To make the presets,

enter the numbers below while referring to the

section “Entering and Setting the Manufacturer

Number Directly”.

TV1: 0001, TV2: 0002

DVD1: 0001, DVD2: 0002

Entering and Setting the Manufacturer Number

Directly

Refer to the manufacturer number list.

This example shows how to set a SAMSUNG DVD

player.

View the supplied manufacturer number list,

and find the number of the manufacturer for

the device that you are using.

Hold down the M button for three seconds or

more.

The menu is displayed.

Press the D1 (PRESET) direct button.

The Preset setting (P-SET) is displayed.

Press the DVD source button.

Press the numeric buttons to enter the four-

digit manufacturer number.

Example: To enter “0600” from the manufacturer

number list.

To correct the entered number, use the

cursor button to enter the correct number.

• If no button is pressed for over one minute

during the setting process, any settings

that were made are cancelled.

Press the OK cursor button.

Confirm the OK is displayed and then the

display returns to the Preset Setting (P-SET).

When the manufacturer number is entered correctly,

OK is displayed momentarily on the screen.

• If you enter a number not in the

manufacturer number list, WRONG CODE

is displayed, and then you return to the

preset setting again

Check the manufacturer number list, and

either set a different number or use the

sequence function to set.

To set the manufacturer number for another

source device, repeat the procedure in steps 4

to 6.

After the settings are completed, press the M

button.

10.

Press the buttons on the remote control to

check that the DVD can be operated correctly.

Setting Equipment Not Appearing in Manufacturer

Number List

Use the sequence function to set equipment not

appearing in the manufacturer number list. You

may still be unable to set some equipment even

when using the sequence function. In this case,

the remote control can be programmed with codes

individually.

In the sequence function, the power ON/OFF

codes are transmitted by pressing the remote

control buttons in order.

If the power for the equipment is left on, hold down

the button until the equipment is turned off, and

then release. This completes the setting.

This example shows how to set a DVD player.

Turn on the power of the DVD player.

Hold down the M button for three seconds or

more.

The menu is displayed.

Press the D1 (PRESET) direct button.

The Preset setting (P-SET) is displayed.

Press the DVD source button.

Hold down the CH+ or CH– button for one

second or more.

Press the CH+ button repeatedly in the

interval for one second.

The signal is transmitted, and the display cycles

through the code number.

Press the CH– button to go back to a number screen.

Release the button once the DVD player turns

off.

Press the OK cursor button.

Confirm the OK is displayed and then the

display returns to the Preset Setting (P-SET).

10.

To set the manufacturer number for another

source device, repeat the procedure in steps 4

to 8.

11.

After the settings are completed, press the M

button.

12.

Press the buttons on the remote control to

check that the DVD can be operated correctly.

Check the following points if the equipment which

was set does not operate properly.

• If there is more than one number in the

manufacturer number list, try setting a different

number.

• There may be some buttons which cannot be

used. Program the codes to the required

buttons.

Remote control Corresponding Device name

source name preset code

TV TV Television

DVD DVD DVD player

VCR VCR Video deck

DSS SATELLITE Satellite broadcasting

tuner equipment

TUNER

RECEIVER/TUNER

AM FM TUNER

CD CD/CD-R PLAYER CD player

CD-R CD/CD-R PLAYER CD recorder

MD CD/CD-R PLAYER MD deck

TAPE TAPE Cassette deck

AUX1 CABLE Cable television

AUX2 LASER DISC Laser disc player

AMP AMPLIFIER Amplifier or receiver

RECEIVER/TUNER

LEARN

45 7

USE

PAG E

LEARN

23 4

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 57 58

Comments to this Manuals

No comments

Marantz SR7500 User Manual Page 43

Comments to this Manuals

Related products and manuals for Acoustics Marantz SR7500