Marantz PMD510 Operations Instructions download pdf (Page 6)

REAR PANEL CONNECTIONS

A LINE INPUT

These jacks should be connected to the LINE OUTPUT of your

source.

B LINE OUTPUT

These jacks should be connected to the LINE INPUT of your PA or

monitoring system.

C INPUT SELECT SWITCH

This switch selects the input mode for the LINE INPUT jacks.

• Position A, B..... Deck A receives its input from LINE INPUT A

Deck B receives its input from LINE INPUT B

• Position A ......... Both decks receive the same input from LINE

INPUT A

D MPX FILTER SWITCH

When recording FM broadcasts with Dolby NR, set this switch to

ON.

E RC-5 REMOTE CONTROL JACKS

These jacks are for use with the Marantz RC5PMD serial remote

control accessory. Connect the output of the remote control to the

RC-5 input of the PMD510. The RC-5 output of the PMD510 may

be connected to the RC-5 input of other machines for multiple-

machine control from the same RC5PMD remote control acces-

sory.

F EXT (EXTENSION) REMOTE CONTROL JACKS

This jack is used to cascade several PMD510s for continuous serial

recording and playback. Connect the EXT OUT jack to the EXT IN

jack of the next unit in the chain.

G AC POWER CONNECTION

With the POWER switch set to OFF, plug the AC line cord into an

AC outlet providing the proper voltage.

FRONT PANEL FEATURES

q POWER SWITCH

For switching the unit on and off.

w CASSETTE HOLDERS

Insert cassettes into these holders with the exposed tape facing

downward.

e EJECT BUTTONS

For opening the cassette doors.

r CONTROL BUTTONS

■STOP

Press this button to cancel any operation modes and to stop tape

travel.

t PLAY (forward)

Press this button to start playback in the forward direction.

r PLAY (reverse)

Press this button to start playback in the reverse direction.

FAST WIND

Press these buttons to fast wind in the direction of the arrows. If

the well is already in play mode, this button will place the well in

CUE/REVIEW Mode.

● REC

Press this button to enter REC-PAUSE mode. Press PLAY to

initiate recording. Press this button again to re-enter REC-PAUSE

mode.

t A+B REC BUTTON

Check to insure that both wells are in STOP mode and the proper

tape direction has been selected, prior to pressing the A+B REC

button. Pressing the A+B REC button once will cause both wells to

enter a REC PAUSE mode to adjust recording levels. Pressing the

A+B REC button a second time, will cause both wells to enter a

REC mode simultaneously. Pressing the A+B REC button a third

time, will cause both wells to enter a REC PAUSE mode again and

pressing the A+B REC button a fourth time, will resume the REC

mode. This operation will continue untll the STOP button has been

pressed for either one or both of the wells.

y CONT (CONTINUOUS) BUTTON

When the CONT button is pressed, the CONT indicator b will light.

Now press PLAY or REC to start continuous recording or playback.

Only use this button when both decks are in the STOP mode. When

the CONT button is pressed again, the indicator will go out, and

continuous mode is cancelled.

u DUBBING BUTTONS

These buttons enable you to sync-start dubbing from WELL A to

WELL B copies the tape. Check to insure that both wells are STOP

mode and the proper tape direction has been selected prior to

press the DUBBING button.

NORMAL SPEED DUBING bottons

Pressing the NORM DUBB button once will cause well A to enter

a STOP/PAUSE mode and well B to enter a REC PAUSE mode.

Pressing the NORM DUBB button a second time, will cause

normal speed dubbing to begin.

HIGH SPEED DUBBING buttons

Pressing the HIGH SPEED button will high speed dubbing being.

i REVERSE MODE SWITCH

With this switch, you can select the autoreverse mode for record-

ing and playback.

: Select this mode to play or record in one direction (no

autoreverse).

: Select this mode to play or record in two directions. When

the end of side B is reached, that Well will enter stop mode.

: Select this mode to continuously play both sides of a tape.

When the end of side B is reached, the tape will autoreverse,

and begin playing side A again, and so on, until the STOP

button is pressed. In REC mode, this mode works just like

the

mode above.

o COUNTER BUTTONS

MEMO buttons

When this button is pressed, MEMO indicator c will light up, and

the position of the tape counter will be stored in memory. When the

tape passes that location during fast winding, the transport will

STOP. When the MEMO button is pressed again, the indicator will

go out, and the memory will be cleared.

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comments to this Manuals

No comments

Marantz PMD510 Operations Instructions Page 6

Comments to this Manuals

Related products and manuals for Cassette players Marantz PMD510