Marantz SR7002 User Manual download pdf (Page 21)

ENGLISH

LEARN MODE

Programming the

(PLAY) and Other Control But-

tons and Numeric Buttons

This remote controller is capable of learning and

storing codes used by other remote controllers that

you already own.

For codes which are not learned, the remote

controller will transmit either the Marantz preset

codes from the initial settings, or remote codes from

another manufacturer’s AV equipment which is set

by the customer.

The receiver sensor for the remote control signals is

located at the top of the remote controller.

This example shows how to learn the codes from the

remote control of a DVD player.

LEARN

NAME

MACRO

USE

PAG E

1 23

LEARN

NAME

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

1 2 4

LEARN

NAME

MACRO

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

6 (When OK) (failed) (codes are full)

LEARN

NAME

MACRO

USE

PAG E

123

Hold down the M button for three seconds or

more.

The menu is displayed.

Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) is displayed. The

LEARN

indicator then blinks.

Press the DVD source button.

Press the 2 (PLAY) button.

The

LEARN

indicator blinks, and then displays to

indicate that learning is ready.

Place the receiver sensor of the remote control

(top) so that it is facing the transmitter of the

DVD remote control (top) at a distance of about

5 cm (2 inches).

Press and hold down the 2 (PLAY) button of the

transmitting DVD remote control, and check that

OK is displayed on the LCD.

The remote controller has finished learning when

OK is displayed on the LCD.

If ERROR is displayed on the LCD, some error has

prevented the command from being learned. If this

happens, repeat the procedure for steps 4 and 5.

In some rare cases, ERROR may be displayed

repeatedly during the learning operation. In this

case, the transmitting remote control may have

special signal codes. These codes cannot be

learned by this remote controller.

Follow the same procedure to make the remote

control learn the other buttons.

Repeat the procedure in steps 3 to 6 to have

the remote control learn the signal codes from

a TV, CD player, or other AV equipment.

• When no buttons are pressed for

approximately one minute during the

learning operation, the remote controller

automatically returns to USE mode.

• When programming the source buttons,

switch to the source in step 3, and then

press the source button again.

9. When you have finished programming the

codes for each button, press the M button.

The

USE

indicator is displayed on the LCD, and the

newly stored codes can be used.

• If FULL is displayed on the LCD, the memory

cannot hold any more learned codes in

LEARN mode.

If FULL is displayed no matter how many

times you try the learning operation, the

remote controller cannot accept any more

new codes until some of the previously

learned codes are deleted from the memory.

Delete some of the learned buttons from the

sources.

The M button and > button cannot be taught. Only

each one code can be learned for the LIGHT buttons

1 and 2, regardless of the source.

Programming the Direct Buttons and Rewriting

Names

This example shows how to program codes from

other manufacturer products to the DVD MENU

button (D1) and change the display to OSD.

LEARN

NAME

MACRO

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

6 7 8

LEARN

NAME

MACRO

USE

PAG E

123

Hold down the M button for three seconds or

more.

The menu is displayed.

Press the D2 (LEARN) direct button.

The LEARN setting (LEARN) indicator is displayed.

The

LEARN

indicator then blinks.

Press the DVD source button.

The first page of the direct button screen is

displayed. There are four available pages. Pressing

the > buttons cycles through the pages in this order

→

Press the D1 (MENU) direct button.

The

LEARN

indicator blinks, and then displays to

indicate that learning is ready.

Place the receiver sensor of the remote control

(top) so that it is facing the transmitter of the

DVD remote control (top) at a distance of about

5 cm (2 inches).

Press and hold down the OSD button of the

transmitting DVD remote control, and check that

OK is displayed on the LCD.

The remote controller has finished learning when

OK is displayed on the LCD.

If ERROR is displayed on the LCD, some error has

prevented the command from being learned. If this

happens, repeat the procedure for steps 4 and 5.

• After learning is completed, the remote

controller automatically switches to name

rewriting mode. The left end “ ” indicator on

the MENU blinks to indicate that the blinking

part can be rewritten.

• If no names will be rewritten, press the

OK cursor button. The display returns to

learning standby mode by pressing the OK

cursor button.

To change the name, press the numeric

buttons to enter the text.

• Use the cursor buttons 1 2 to move to the

sections to be rewritten on the LCD.

• To change MENU to OSD, press the 5

numeric button.

Each time the button is pressed, the display

cycles through M → N → O → 5 → M.

After rewriting of the text is completed, press

the OK cursor button.

To delete text that is already entered, press the

button to insert a space.

• In this example, MENU is changed to “OSD

(space) (space)” in this step, and then OSD

is displayed in the right side by pressing the

OK button.

For details, refer to the section “Rewriting Names”.

In the same way, use the > button to select

the page, and then press the direct button to

program the codes.

10.

After programming the codes for each of the

buttons, press the M button.

The

USE

indicator displays on the LCD, and the

newly stored codes can be transmitted.

REWRITING NAMES

This remote controller allows the rewriting of names

for the sources and direct buttons. This operation is

performed for each individual source.

This example shows how to change the source name

from DVD to AVD and AUDIO to SOUND.

LEARN

NAME

MACRO

USE

PAG E

123

3 4 5

LEARN

NAME

MACRO

USE

PAG E

123

7 8 9

LEARN

NAME

MACRO

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

LEARN

NAME

MACRO

USE

PAG E

123

Hold down the M button for three seconds or

more.

The menu is displayed.

Press the D3 (NAME) direct button .

SR7002-8002_U_01_ENG 1_3.indd 18SR7002-8002_U_01_ENG 1_3.indd 18 07.8.24 1:14:49 PM07.8.24 1:14:49 PM

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 93 94

Comments to this Manuals

No comments

Marantz SR7002 User Manual Page 21

Comments to this Manuals

Related products and manuals for AV receivers Marantz SR7002