Marantz SR7002 User Manual download pdf (Page 35)

ENGLISH

CONNECTING AUDIO COMPONENTS

OUT IN

DIGITAL

INPUT

DIGITAL

OUTPUT

OUT IN

L R

RL RL

R L

R L R L

L R

The output audio signal from the TAPE OUT jack and

the CD/CD RECORDER OUT jack is the same signal

which is currently selected.

Caution:

• Do not connect this unit and other components

to mains power until all connections between

components have been completed.

Notes:

• Insert all plugs and connectors securely. Incomplete

connections may make noise.

• Be sure to connect the left and right channels

properly.

Red connectors are for the R (right) channel, and

white connectors are for the L (left) channel.

• Be sure to connect input and output properly.

• Refer to the instructions for each component that is

connected to this unit.

• Do not bind audio/video connection cables with

power cords and speaker cables this will result in

generating a hum or other noise.

CONNECTING DIGITAL AUDIO COMPONENTS

• There are 6 digital inputs, 3 coaxial jacks and

3 optical jacks, on the rear panel. You can use

these jacks to input PCM, Dolby Digital and DTS

bitstream signals from a CD, DVD, or other digital

source components.

• There is one digital output coaxial jack and one

optical output jack on the rear panel. These jacks

can be connected to a CD recorder, or a MD deck

inputs, respectively.

• Refer to the instructions for each component. To

setup the digital audio format of DVD player, or

other digital source’s connected to digital input

jacks.

• Use ﬁ ber optical cables (optical) for DIG-1,2,3

input jacks. Use 75 ohms coaxial cables (for digital

audio or video) for DIG-4, 5, 6 input jacks.

• You can designate the input for each digital input/

output jacks according to your component. See

page 43.

CD recorder

Tape Deck

Analog Audio

Digital Audio (coaxial)

Digital Audio (optical)

Notes:

• There is no Dolby Digital RF input jack. Use an

external RF demodulator Dolby Digital decoder

when connecting the Dolby Digital RF output jack

of the videodisc player to the digital input jack.

• The digital signal jacks on this unit conform to

the EIA standard. If you use a cable that does not

conform to this standard, this unit may not function

properly.

• Each type of audio jack works independently.

Signals input through the digital and analog jacks are

output through the corresponding digital and analog

jacks, respectively.

Caution:

•

Be sure to use speakers with the speciﬁ ed impedance as

shown on the rear panel of this unit.

•

To prevent damage to circuitry, do not let the bare

speaker wires touch each other and do not let them

touch any metal part of this unit.

• Do not touch the speaker terminals when the

power is on. It may cause you to receive an electric

shocks.

• Do not connect more than one speaker cable to one

speaker terminal. Doing so may damage this unit.

Note:

•

Be sure to connect the positive and negative cables for

the speaker properly. If they are miss-connected, the

signal phase will be reversed and the signal quality will

be corrupted.

CONNECTING A SUBWOOFER

Use the PRE OUT SUBWOOFER jack to connect a

powered subwoofer (power ampliﬁ er built in ).

If your subwoofer is a passive type (power ampliﬁ er

is not built in), connect a monaural power ampliﬁ er to

the PRE OUT SUBWOOFER jack and connect the

subwoofer to the ampliﬁ er.

SR7002-8002_U_01_ENG 2_3.indd 32SR7002-8002_U_01_ENG 2_3.indd 32 07.8.24 1:15:19 PM07.8.24 1:15:19 PM

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 93 94

Comments to this Manuals

No comments

Marantz SR7002 User Manual Page 35

Comments to this Manuals

Related products and manuals for AV receivers Marantz SR7002