Marantz SR7002 User Manual download pdf (Page 33)

ENGLISH

30

CLONE MODE

Creating copies using clone mode

All of the codes programmed to the RC101 remote

controller can be copied to another RC101 using a

few simple operations.

• The remote controller can copy the entire

contents.

• When copying the entire contents, all programmed

codes are copied.

Note:

The clone function can only be used for copying

when using the same model (RC101) for both the

transmitting and receiving remote controller.

Copying entire contents

1. Place the receiver sensor of the receiving

remote controller (top) so that it is facing the

transmitter of the transmitting remote controller

(top) at a distance of about 2 inches (5 cm).

2 inches

S

Y

S

T

E

M

R

E

M

O

TE

C

O

N

T

R

O

L

L

E

R

S

YS

T

E

M

R

E

M

O

T

E

C

O

N

T

R

O

L

L

E

R

2. Press SET button and PLAY button of the

transmitting remote controller until the SEND

indicator blinks twice.

Then backlight ﬂ ashes

The transmitting side is now ready.

3. Press SET button and STOP button of the

receiving remote controller until the LEARN

indicator blinks twice.

Then backlight ﬂ ashes.

The receiving side is now ready.

4. Press the ENTER cursor button on the receiving

remote controller.

Then back lights tune off.

5. Press the ENTER cursor button on the

transmitting remote controller.

Then backlights tune off.

6. When copying is started, the SEND indicator of

transmitting remote controller and the LEARN

indicator of receiving remote controller start to

blink.

When the copying operation is completed, the

back lights of transmitting remote controller and

receiving remote controller are turned on.

Do not touch either of the remote controls

during the copying operation. Doing so could

cause copying to fail.

If the copying fails in the middle of the copying

process, back light of receiving remote are

flash. Press the SET button to return the

normal mode. Check and perform steps 1 to 5

again.

Copying takes about 30 seconds to complete

when the transmitting remote controller has

been programmed to 100% capacity.

7. Once copying is completed, press the SET

button on both remote controls.

OTHER OPERATIONS

CHANGE THE MULTI ROOM CONTROL COMMANDS

FOR EACH ZONE

(When operating the unit by Multi Zone connected)

• Zone A: MULTI ROOM A Control (Default)

• Zone B: MULTI ROOM B Control

(The SR7002 does not use this zone.)

• Zone C: The unit does not use this zone.

• Zone D: MAIN ROOM

Change the control commands for each zone.

2.

1.

1. Press SET button and ZONE button until the

SEND indicator blinks twice.

Then backlight ﬂ ashes.

2. Press each zone button(A/B button)

When the procedure is successful, the SEND

indicator will blink twice.

These buttons change a special code of each zone.

POWER ON/OFF

SOURCE

INFO

VOL +/–

SLEEP

MUTE

Tuner mode operation remote code (Refer to p.26)

CHANGE THE CONTROL COMMANDS OF MULTI

SPEAKER FUNCTION FROM MULTI ROOM.

1.

2.

1.

3.

1. Press SET button and POWER ON button until

the SEND indicator blinks twice.

Then backlight ﬂ ashes.

2. Press the 1-digit code by numeric keys.

• Multi room mode: 1 (Default)

• Multi speaker mode: 2

Note

In case of Zone D, only control for main room is

possible.

3. Press ENTER button once to lock in the code.

When the procedure is successful, the SEND

indicator will blink twice.

These buttons change a special code of multi room

mode or multi speaker mode.

Note

The control commands can be set independently in

ZONE A/B.

POWER ON/OFF

VOL +/–

MUTE

SR7002-8002_U_01_ENG 1_3.indd 30SR7002-8002_U_01_ENG 1_3.indd 30 07.8.24 1:14:58 PM07.8.24 1:14:58 PM

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 93 94

Comments to this Manuals

No comments