Marantz SR6005 User Manual Page 13
- Page / 104
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
9
Basic version Advanced version Information
ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA
Simple version
Set up speakers (Audyssey
®
Auto Setup)
STEP 1
Preparation
• In STEP 2, you will perform measurements at
multiple positions (two to six positions) other than
the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
Move the setup microphone to position
2, use ui to select “Measure”, and
then press ENTER.
The measurement of the second position
starts. Measurements can be made in up to
six positions.
[3/6]
STEP3 Measurement
Please place the mic-
rophone at ear height
at 2nd listening
position.
Start next measurement. Test Tone will start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
Measure
Next Calculation
MultEQ
If you want to omit measurements from the next
position onward, select “Next 1 Calculation”.
(Go to
STEP4 Calculation
)
10
Repeat step 9, measuring positions 3
to 6.
When measurement of position 6 is
completed, a “Measurements finished.”
message is displayed.
[3/6]
STEP3 Measurement
Measurements finished.
Proceed to Step 4 (Analyze)
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
Retry
Next Calculation
MultEQ
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 11), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER.
When measuring has stopped
Press RETURN, to the “Cancel Auto Setup?”
prompt is displayed.
Press o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation
.
STEP 2
Speaker Detection
STEP 3
Measurement
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
configuration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
Select “Measure” and then press
ENTER.
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7
The detected speakers are displayed.
[2/6]
STEP2 Spkr Detect Check
Go to Step 3 (Measurement) after speaker check
Retry
Next Measurement
Front
Center
Subwoofer
Surround
S.Back
Yes
Yes
Yes
Yes
2spkrs
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
MultEQ
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use ui to select “Next 1
Measurement” and then press ENTER.
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Start Auto Setup
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ
ENTER Enter RETURN Cancel
When the setup microphone is
connected, the following screen is
displayed.
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select “Amp
Assign” and perform step 3 and 4 of “Set up
“Amp Assign”” (vpage39).
If unused channels are set with “Channel
Select”, measuring time can be shortened. For
setting, perform steps 5 to 9 of “Set up “Channel
Select”” (vpage39).
5
Use ui to select “Auto Setup Start”
and then press ENTER.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
- AV Surround Receiver 1
- IMPORTANT SAFETY 3
- INSTRUCTIONS 3
- PRÉCAUTIONS D’INSTALLATION 4
- Getting started 5
- Features 6
- Accessories 6
- About this manual 6
- Cautions on handling 7
- Speakers 9
- Blu-ray Disc player and TV 10
- Power on 11
- Preparation 13
- Speaker Detection 13
- Measurement 13
- Calculation 14
- Parameter Check 15
- Error messages 15
- BD two times in a row 16
- Basic version 17
- Connections 18
- Connecting a TV 21
- Cables used for connections 22
- Supported iPod models 23
- Connecting a CD player 24
- Connecting an antenna 24
- n AM loop antenna assembly 25
- n Using the AM loop antenna 25
- Suspending on a wall 25
- Standing alone 25
- SPKR A/B 27
- Playing a CD player 28
- Playing a USB memory device 28
- n USB operation 29
- ON to turn on power to the 30
- NET/USB twice to switch 30
- ENTER, p or 1 30
- SATR twice to switch the 31
- TUNING + or TUNING – to 31
- 1, 2 and 3 32
- Tuning in radio stations 32
- n Parental Lock 33
- n SIRIUS operation 33
- n Selecting audio programs 33
- SHIFT/TOP MENU to select 34
- PRESET +, PRESET – or 34
- SEARCH/INFO 34
- STATUS while an HD Radio 34
- SURR. to select the 35
- P.DIRECT to select the 37
- SURR. to select “DOLBY 37
- Advanced version 38
- 5.1-channel connection 41
- Front A/B connection 41
- 2.1-channel connection 42
- Bi-Amp connection 42
- Set up speakers 43
- REMOTE CONTROL jacks 44
- RS-232C connector 45
- DC OUT (TRIGGER OUT) jacks 45
- Playback (Advanced operation) 46
- Sleep timer function 47
- Panel lock function 48
- Various memory functions 48
- Connection (ZONE2) 49
- Z2 to switch the remote 50
- ON to turn on the ZONE2 50
- INPUT df 50
- How to make detailed settings 51
- ENTER to register it 53
- Input Setup 54
- Auto Preset 55
- Antenna Aiming 56
- Preset Name 56
- Input Assign 56
- Playback Mode 59
- Audio/Video Adjust 60
- n Audyssey Settings 61
- Audyssey Dynamic EQ is 62
- n Manual EQ 63
- n M-DAX 63
- n Audio Delay 63
- Manual Setup 65
- MULTEQ is pressed 68
- Other settings 72
- Operating AV equipment 73
- Registering preset codes 74
- SET until indicator blinks 75
- SET and 76
- SOURCE SEL until the LEARN 76
- Operating macro function 78
- Setting the back light 79
- Information 80
- Part names and functions 81
- Rear panel 83
- Remote control unit 84
- Inserting the batteries 85
- Other information 86
- Surround 87
- Symbols in the table 89
- Explanation of terms 92
- Troubleshooting 94
- Resetting the microprocessor 96
- Specifications 97
- Blu-ray Disc Player 101
- DVD Player 101
- Satellite Receiver 101
- Television 101
- CD Player 102
- Unit : mm (in) 103
- D&M Holdings Inc 104
Related products and manuals for Receivers and Amplifiers Marantz SR6005
(15 pages)
(104 pages)
(104 pages)© 2020, manymanuals.com. All rights reserved. | 0.462 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals