Marantz SR7002 User Manual Page 25
- Page / 94
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ENGLISH
22
SETTING THE MACRO TIMER
Setting the macro timer enables the macro program
to automatically turn the power for a device on or off
or perform other operations.
In the settings, you can select to execute the macro
timer everyday or only once.
Be sure to set the clock to the correct time before
using the timer. The macro timer can only be set for
one program a day.
This example shows how to use the timer only once
at 20:35 to execute a macro programmed to M-01.
2 3 4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
5 6
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the > button to display the third page
TIMER menu.
3.
Press the D2 (ONCE?) direct button.
The M-TMR menu is displayed on the LCD.
• To cancel timer operation, press CANCEL.
4.
Press the D1 (M-01) direct button .
The time which is set previously is displayed.
5.
Press the 2 and 0 numeric button to set the
hour indicator to 20.
6.
Press the 3 and 5 numeric button to set the
minute indicator to 35.
7.
Press the OK cursor button.
This fi nalizes the time.
8.
To exit, press the M button.
To cancel the macro timer, return to the TIMER
menu and press the D5 (CANCEL) and then press
D1 (M-01).
EXECUTING THE MACRO TIMER
The macro program starts when the time that was
set is reached. The TIMER indicator lights up
whenever the macro timer is activated.
Note:
• To execute the macro timer, place the remote
controller facing the infrared sensor of the device
to be operated. If the remote controller is not in
a suitable position, it may not operate the device
properly.
CLONE MODE
CREATING COPIES USING CLONE MODE
All of the codes programmed to the RC8001SR remote
controller can be copied to another RC8001SR using
a few simple operations.
• The remote controller can copy the entire contents
or the contents for specifi c source buttons.
• When copying the entire contents, all programmed
codes, modifi ed names, programmed macros, and
signal transmission intervals are copied.
When copying the contents for source buttons, the
programmed codes and modifi ed names are copied.
Note:
• The clone function can only be used for copying
when using the same model (RC8001SR) for both
the transmitting and receiving remote controller.
COPYING ENTIRE CONTENTS
<Transmitting remote controller>
3 4 9
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
<Receiving remote controller>
5 6 9
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Place the receiver sensor of the receiving
remote control (top) so that it is facing the
transmitter of the transmitting remote control
(top) at a distance of about 5 cm (2 inches).
2.
Hold down the M button of the transmitting
remote controller for three seconds or more.
The menu is displayed.
3.
Press the > button to display the fourth page
CLONE menu.
4.
Press the D3 (TX) direct button.
The transmitting side is now ready.
5.
Hold down the M button of the receiving remote
controller for three seconds or more.
The menu is displayed.
6.
Press the > button to display the fourth page
CLONE menu.
7.
Press the D1 (RX) direct button.
The receiving side is now ready.
8.
Press the OK cursor button on the receiving
remote controller.
9.
Press the OK cursor button on the transmitting
remote controller.
When copying is started, the bar indicators on both
LCDs start to move from the left to the right.
• When the copying operation is completed,
TX OK is displayed on the LCD of the
transmitting remote controller, and RX OK
is displayed on the LCD of the receiving
remote controller.
• Do not touch either of the remote controllers
during the copying operation. Doing so
could cause copying to fail.
• If the copying fails in the middle of the
copying process, RX ERROR is displayed
on the receiving remote controller. Check
and perform steps 1 to 7 again.
• Copying takes about three minutes to
complete when the transmitting remote
controller has been programmed to 100%
capacity.
10.
Once copying is completed, press the M button
on both remote controllers.
COPYING BY SOURCE
The 12 sources can be copied on a source by source
basis. You can select from up to 12 source types.
<Receiving remote controller>
6 7 8
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Place the receiver sensor of the receiving
remote control (top) so that it is facing the
transmitter of the transmitting remote control
(top) at a distance of about 5 cm (2 inches).
2.
Hold down the M button of the transmitting
remote controller for three seconds or more.
The menu is displayed.
3.
Press the > button to display the fourth page
CLONE menu.
4.
Press the D3 (TX) direct button.
The transmitting side is now ready.
5.
Hold down the M button of the receiving remote
controller for three seconds or more.
6.
Press the > button to display the fourth page
CLONE menu.
7.
Press the D2 (RX-S) direct button.
8.
Press the source button to be copied.
The receiving side is now ready.
The name of the source which was pressed is
displayed on the LCD.
• Each time the source button is pressed, the
name is displayed on the LCD.
9.
Press the OK cursor button on the receiving
remote controller.
10.
Press the OK cursor button on the transmitting
remote controller.
When copying is started, the bar indicators on both
LCDs start to move from the left to the right.
• When the copying operation is completed,
TX OK is displayed on the LCD of the
transmitting remote controller, and RX OK
is displayed on the LCD of the receiving
remote controller.
• Do not touch either of the remote controllers
during the copying operation. Doing so
could cause copying to fail.
• If the copying fails in the middle of the
copying process, ERROR is displayed on
the remote controller.
Check and perform steps 1 to 7 again.
SR7002-8002_U_01_ENG 1_3.indd 22SR7002-8002_U_01_ENG 1_3.indd 22 07.8.24 1:14:54 PM07.8.24 1:14:54 PM
- AV Surround Receiver 1
- IMPORTANT SAFETY 2
- INSTRUCTIONS 2
- DECLARATION OF CONFORMITY 3
- INTRODUCTION 4
- TABLE OF CONTENTS 5
- FEATURES 5
- DESCRIPTION 6
- BEFORE USE 9
- REMOTE CONTROL 10
- LOADING BATTERIES 10
- CAUTIONS ON BATTERIES 10
- NAMES AND FUNCTION 11
- SURROUND 12
- REAR PANEL 13
- OPERATION (RC8001SR) 14
- SETTING THE TIME 16
- Learning Remote Controller 17
- RC8001SR 17
- BASIC OPERATION 20
- ERASING PROGRAMMED CODES 22
- Erasing Direct Button Pages 22
- Erasing Sources 22
- PROGRAMMING MACROS 23
- CLEARING MACRO PROGRAMS 24
- CLONE MODE 25
- SETTING THE LIGHTING TIME 26
- OPERATION (RC101) 27
- CONTROLLING A MARANTZ TV (TV) 28
- LEARN MODE 32
- LEARNING PROCEDURE 32
- INITIAL SETTINGS) 32
- OTHER OPERATIONS 33
- CONNECTIONS 34
- CONNECTING AUDIO COMPONENTS 35
- CONNECTING VIDEO COMPONENTS 36
- HDMI OUTPUT HDMI INPUT 37
- HDMI OUTPUT 37
- ADVANCED CONNECTING 38
- FM ( 575 )) GNDGND AMAM 39
- ANTANTENNA 39
- XM RADIO OVERVIEW 40
- CONNECTING FOR THE MULTI ROOM 41
- MULTIROOM B 41
- MULTIROOM A 41
- CONNECTING OTHER EQUIPMENT 42
- RC8001SR BUTTON CONTROL 43
- 1 INPUT SETUP 45
- 1-1 FUNC INPUT SETUP 46
- (ASSIGNABLE DIGITAL INPUT) 46
- 1-2 7.1 CH INPUT SETUP 46
- 1-3 FUNCTION RENAME 47
- 2 SPKR (SPEAKER) SETUP 48
- AV SURROUND RECEIVER SR8002 49
- ERROR MESSAGES 51
- 2-2 MANUAL SETUP 52
- <SPEAKER SIZE> 52
- <SPEAKER DISTANCE> 52
- <SPEAKER LEVEL> 53
- 2-3 THX AUDIO SETUP 53
- 3 SURROUND SETUP 54
- 4 VIDEO SETUP 56
- 5 PREFERENCE 57
- 5-1 MULTI ROOM SETUP 58
- 5-2 DC TRIGGER SETUP 58
- 6 ACOUSTIC EQ 59
- 6-2 CHECK AUTO 60
- 6-1 PRESET G. EQ ADJ 60
- ANALOG VIDEO CONVERSION 62
- SIGNALS TO HDMI 62
- CONNECTION EXAMPLE 62
- SURROUND MODE 63
- OTHER FUNCTION 67
- DOLBY HEADPHONE MODE 68
- SPEAKER A/B 68
- 7.1 CH INPUT 68
- AUX2 INPUT 69
- VIDEO ON/OFF 69
- TV AUTO ON/OFF FUNCTION 69
- LIP.SYNC 69
- DUAL BACKUP MEMORY 69
- PRESET MEMORY 71
- PRESET CHANNEL LIST DISPLAY 72
- RECALLING A PRESET STATION 72
- PRESET SCAN 72
- SORTING PRESET STATIONS 72
- (SR8002 ONLY) 73
- SELECTING MULTICAST CHANNELS 75
- FM WXYZ-FM 2 75
- PTY AUTO SEARCH 75
- RBDS OPERATION (SR8002 ONLY) 76
- SEARCH MODE 78
- NEURAL SURROUND MODE 80
- MULTI ROOM 81
- (RC101) FOR MULTIROOM A 82
- (RC101) FOR MULTIROOM B 82
- TROUBLESHOOTING 83
- XM SATELLITE RADIO 84
- HD Radio RECEPTION 84
- TECHNICAL SPECIFICATIONS 85
- SETUP CODES 86
- (RC8001SR) 86
- Source button name : TV 88
- Source button name : VCR 89
- Source button name : DVD 90
- DIRECT BUTTON 91
- FUNCTIONS (RC8001SR) 91
Related products and manuals for AV receivers Marantz SR7002
AV receivers Marantz SR5400U User Manual
(36 pages)
(36 pages)
AV receivers Marantz SR4300 User Manual
(44 pages)
(44 pages)
AV receivers Marantz ZR6001 User Manual
(73 pages)
(73 pages)
AV receivers Marantz SR5200 User Manual
(33 pages)
(33 pages)
AV receivers Marantz SR7001 User Manual
(79 pages)
(79 pages)
AV receivers Marantz SR4400 User Manual
(36 pages)
(36 pages)
AV receivers Marantz SR5001 User Manual
(51 pages)
(51 pages)
AV receivers Marantz SR7200 User Manual
(39 pages)
(39 pages)
AV receivers Marantz SR4002 Datasheet
(2 pages)
(2 pages)
AV receivers Marantz SR6008 Owner's Manual
(247 pages)
(247 pages)
AV receivers Marantz SR5009/N1SG Owner's Manual
(270 pages)
(270 pages)
AV receivers Marantz NR1504 Owner's Manual
(60 pages)
(60 pages)
AV receivers Marantz SR7005B User's Guide
(124 pages)
(124 pages)
AV receivers Marantz AV8003 User's Guide
(92 pages)
(92 pages)
AV receivers Marantz SR5006B Owner's Manual
(146 pages)
(146 pages)
AV receivers Marantz SR5008 Owner's Manual
(238 pages)
(238 pages)
AV receivers Marantz MCR503 User's Guide
(43 pages)
(43 pages)
AV receivers Marantz MCR603 User's Guide
(56 pages)
(56 pages)
AV receivers Marantz SR6006 Owner's Manual
(153 pages)
(153 pages)
AV receivers Marantz SR4002 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals